$25.2 Buy It Now or Best Offer
free,30-Day Returns

Seller Store cfspeed-autoparts
(545) 98.9%,

Location: Ontario, California, United States
Ships to: US,
Item: 404636478976

Condition:New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is … Read moreabout the conditionNew: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller’s listing for full details. See all condition definitionsopens in a new window or tab
cfspeed-autoparts:cfspeed-autoparts
Manufacturer Part Number:C10064201APS
Items Included:Mounting Hardware
Fitment:For Dodge,Plymouth
Store Speciality:Suspension & Steering
Interchange Part Number:K7106
Surface Finish:Polished, Rust Protected
Universal Fitment:No
Placement on Vehicle:Left, Right, Front
UPC:Does not apply
Kit or Single Part:Single
Quantity:1Piece
Manufacturer Warranty:10 Year
Kit Parts Included:Idler arm
OE/OEM Part Number:488946
Adjustable:Yes
Greasable or Sealed:Greasable
Type:Idler Arm
Features:Greasable
Finish:Coated

eBay 1.Fit For DODGE B100 1979-1980 DODGE B150 1981-1994 DODGE B1500 1995-1998 DODGE B200 1979-1980 DODGE B250 1981-1994 DODGE B2500 1995-1998 DODGE B300 1979-1980 DODGE B350 1981-1994 DODGE B3500 1995-1998 DODGE CB300 1979-1980 DODGE RAM 1500 VAN 1999-2003 DODGE RAM 2500 VAN 1999-2003 DODGE RAM 3500 VAN 1999-2003 PLYMOUTH PB100 1979-1980 PLYMOUTH PB150 1981-1983 PLYMOUTH PB200 1979-1980 PLYMOUTH PB250 1981-1983 PLYMOUTH PB300 1979-1980 PLYMOUTH PB350 1981-1983 2.Package Includes: 1 x Part# Idler arm – K7106 Cfspeed-autoparts BRAND NEW 1PC Steering Idler Arm Kit K7106 For Dodge B200 B250 B100 B150 B1500 1.Fit For DODGE B100 1979-1980 DODGE B150 1981-1994 DODGE B1500 1995-1998 DODGE B200 1979-1980 DODGE B250 1981-1994 DODGE B2500 1995-1998 DODGE B300 1979-1980 DODGE B350 1981-1994 DODGE B3500 1995-1998 DODGE CB300 1979-1980 DODGE RAM 1500 VAN 1999-2003 DODGE RAM 2500 VAN 1999-2003 DODGE RAM 3500 VAN 1999-2003 PLYMOUTH PB100 1979-1980 PLYMOUTH PB150 1981-1983 PLYMOUTH PB200 1979-1980 PLYMOUTH PB250 1981-1983 PLYMOUTH PB300 1979-1980 PLYMOUTH PB350 1981-1983 2.Package Includes: 1 x Part# Idler arm – K7106 3.Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may « wander » as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Brand cfspeed-autoparts Manufacturer Part Number C10064201APS Items Included Mounting Hardware Fitment For Dodge,Plymouth Store Speciality Suspension & Steering Interchange Part Number K7106 Surface Finish Polished, Rust Protected Universal Fitment No Placement on Vehicle Left, Right, Front Kit or Single Part Single Quantity 1Piece Manufacturer Warranty 10 Year Kit Parts Included Idler arm OE/OEM Part Number 488946 Adjustable Yes Greasable or Sealed Greasable Greasable or Sealed Greasable Type Idler Arm Features Greasable Finish Coated Payment PayPal preferred. Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Shipping Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days. We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay. The tracking number will be given for the customer to check the shipping status online (registered or faster service only). We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Returns WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. We stand behind every product we sell. All of our brand new items come with a 60-Days money-back guarantee. We define the item as defective only if it doesn’t function as described. It is the buyer’s responsibility to understand the item description before bidding. We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. Shipping & handling cost are not refundable. Man-made damage by abuse or wrong operation is not covered by this warranty. No product liability insurance is assumed. Contact Us We are dedicated to provide high quality products and satisfied customer service to our sincerely customers, so if there’s any questions or problems with our products or service, feel free to contact us please. Cfspeed-autoparts DESCRIPTION PAYMENT SHIPPING RETURN POLICY CONTACT US Shop Category Store Home Suspension Parts ◈ Air Strut Assembly ◈ Air Spring ◈ Air Suspension Compressor ◈ Solenoid Valve Block Truck & Trailer Springs Vehicles ◈ Audi ◈ Bentley ◈ BMW ◈ Buick ◈ Cadillac ◈ Chevrolet ◈ Citroen ◈ Dodge ◈ Ford ◈ GMC ◈ Hyundai ◈ Infiniti ◈ Isuzu ◈ Jaguar ◈ Jeep ◈ Kia ◈ Land Rover ◈ Lexus ◈ Lincoln ◈ Mercedes-Benz ◈ Mercury ◈ Oldsmobile ◈ Porsche ◈ Saab ◈ Toyota ◈ Volkswagen Suspension Kits Air suspension valves solenoid Shocks & Struts Struts & Suspension Kit & Hubs coilovers complete strut battery Switch window tint film Brake System Parts ◈ Brake Calipers ◈ Brake Drums & Brake Shoes Lift Supports Bumper Assembly Steering Knuckle Mass Air Flow Sensor Strut Mount air dryer Power Brake Booster trim tilt motor Removal Tool Control Arm Camber Arm Other Hot Item 4PCS Front + Rear Air Suspension Shock Strut For Range Rover Sport LR4 LR3 HSE USD 541.07 Rear Pair Air Suspension Air Spring For Lincoln Town Car Mercury Grand Marquis USD 65.87 4PCS Front Rear Complete Strut & Spring Assemblies For 2003-2008 Toyota Corolla USD 187.93 Air Suspension Air Spring W01-358-9978 For Firestone 1T15M4 Hendrickson S-28929 USD 87.95 6Pcs Front Inner Outer Tie Rod Ends For 1988-1999 Chevy GMC K1500 K2500 K3500 USD 41.49 Picture New List Item Front Upper Control Arm Kit For Lexus GX460 GX470 Toyota 4Runner Cruiser K620063 USD 37.28 Front Suspension Lower Forward Control Arm Fits Mercedes C230 C350 CL30 K620086 USD 44.40 Suspension Front Upper Control Arm For Ford Ranger & Mazda B2500 B3000 K8708T USD 40.87 Front Suspension Upper Right Control Arm Fit For Acura CL TL Honda Accord USD 32.14 Rear Lower Trailing Control Arm Assembly For Jeep Grand Cherokee 99-04 K641869 USD 41.93 Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us BRAND NEW 1PC Steering Idler Arm Kit K7106 For Dodge B200 B250 B100 B150 B1500 1.Fit For DODGE B100 1979-1980 DODGE B150 1981-1994 DODGE B1500 1995-1998 DODGE B200 1979-1980 DODGE B250 1981-1994 DODGE B2500 1995-1998 DODGE B300 1979-1980 DODGE B350 1981-1994 DODGE B3500 1995-1998 DODGE CB300 1979-1980 DODGE RAM 1500 VAN 1999-2003 DODGE RAM 2500 VAN 1999-2003 DODGE RAM 3500 VAN 1999-2003 PLYMOUTH PB100 1979-1980 PLYMOUTH PB150 1981-1983 PLYMOUTH PB200 1979-1980 PLYMOUTH PB250 1981-1983 PLYMOUTH PB300 1979-1980 PLYMOUTH PB350 1981-1983 2.Package Includes: 1 x Part# Idler arm – K7106 3.Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may « wander » as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Brand : cfspeed-autoparts Manufacturer Part Number : C10064201APS Items Included : Mounting Hardware Fitment : For Dodge,Plymouth Store Speciality : Suspension & Steering Interchange Part Number : K7106 Surface Finish : Polished, Rust Protected Universal Fitment : No Placement on Vehicle : Left, Right, Front Kit or Single Part : Single Quantity : 1Piece Manufacturer Warranty : 10 Year Kit Parts Included : Idler arm OE/OEM Part Number : 488946 Adjustable : Yes Greasable or Sealed : Greasable Greasable or Sealed : Greasable Type : Idler Arm Features : Greasable Finish : Coated Payment PayPal preferred. Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Shipping Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days. We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay. The tracking number will be given for the customer to check the shipping status online (registered or faster service only). We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Returns WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. We stand behind every product we sell. All of our brand new items come with a 60-Days money-back guarantee. We define the item as defective only if it doesn’t function as described. It is the buyer’s responsibility to understand the item description before bidding. We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. Shipping & handling cost are not refundable. Man-made damage by abuse or wrong operation is not covered by this warranty. No product liability insurance is assumed. Contact Us We are dedicated to provide high quality products and satisfied customer service to our sincerely customers, so if there’s any questions or problems with our products or service, feel free to contact us please. All rights reserved.

Frequently Asked Questions About Steering Idler Arm Replacement K7106 For Dodge B200 B250 B100 B150 B1500 in My Website

www.parlonsofficine.fr is the best online shopping platform where you can buy Steering Idler Arm Replacement K7106 For Dodge B200 B250 B100 B150 B1500 from renowned brand(s). www.parlonsofficine.fr delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling Steering Idler Arm Replacement K7106 For Dodge B200 B250 B100 B150 B1500 on www.parlonsofficine.fr?

www.parlonsofficine.fr helps you to shop online and delivers Abercrombie Fitch to your doorstep. The best-selling Abercrombie Fitch on www.parlonsofficine.fr are: ABERCROMBIE & FITCH ~ AUTHENTIC SELF MENS EAU DE TOILETTE SPRAY ~ 3.4 OZ Abercrombie & Fitch Black Faux Leather 90’s Relaxed High Rise Curve Love Size 20 Abercrombie & Fitch Jeans Women’s Blue Ankle Straight Ultra High Rise Sz 27/4R Abercrombie Fitch Size 22R 90’s Relaxed High Rise Curve Love Denim Stretch Jeans Abercrombie & Fitch Shirt Large Mens Gray Short Sleeve Preppy Top Cotton Tee Abercrombie & Fitch Linen Shorts Mens 38 Navy Blue Stripe Flat Front Casual Abercrombie Fitch Shirt Mens XL Blue Striped Muscle Long Sleeve Crew Neck Tee Abercrombie & Fitch T-Shirt Sz XL Tank Top Basketball Muscle Tee Abercrombie &Fitch Los Angeles Lakers Graphic Shirt XL Relaxed Fit Abercrombie & Fitch Jeans Mens Size 28 x 30 Blue Denim Button Fly *READ* ABERCROMBIE & FITCH MENS XXL 2XL GREEN T SHIRT GOOD USED CONDITION Abercrombie and Fitch shirt men large Blue short sleeve soft A&F longline Abercrombie & Fitch perfume No.1 Undone ABERCROMBIE & FITCH FIRST INSTINCT TOGETHER EDT M 100ML Abercrombie & Fitch Jeans Womens 0 Medium Wash Denim Distressed Thrash Destroyed Abercrombie Fitch Jeans Womens 26 Blue Medium Wash Distressed Moto Skinny Zip First Instinct Together by Abercrombie & Fitch 3.4 oz Men Abercrombie & Fitch Mens Size M Red Long Sleeve Shirt Yellow Striped Sleeve Abercrombie & Fitch T-Shirt – White – XL – Soft AF Abercrombie & Fitch Women’s Sz 10 Jeans Wide Crop Leg Distressed Button Fly A&F New York Long Sleeve Size Large Muscle Abercrombie And Fitch Abercrombie & Fitch Shirt Mens Medium Orange Muscle Long Sleeve Moose Logo VTG Sz L Abercrombie & Fitch Men’s Long Sleeve Waffle Knit Henley Light Blue FLAW Abercrombie Curve Love Black Denim Ultra High Rise Ankle Straight Jean Size 27/4 Vintage Abercrombie Fitch Mens Shirt Medium Blue Henley Muscle Textured Logo Vintage Abercrombie & Fitch Logo in Maroon sz L Abercrombie and Fitch Men’s Muscle Henley S/S Tee Abercrombie & Fitch Fragrance Collection / Collection De Fragrances 6 Perfume, Abercrombie & Fitch 90’s Straight Ultra High Rise Jeans Women Size 4 Abercrombie & Fitch The ‘90s Straight Ultra High Rise jeans 8/29R Abercrombie & Fitch Muscle Shirt Medium Vintage Distressed Abercrombie & Fitch T Shirt Long Sleeve Charcoal Gray Mens Size M Abercrombie and Fitch Shirt Adult Small Gray Garment Dyed V-Neck Distressed Tee Abercrombie & Fitch T Shirt Youth XL Brown Football Graphic Exposed Seams Tee Men’s Abercrombie & Fitch T-shirt Short Sleeve Crew Gray Size XS Panther Cougar Abercrombie & Fitch T-Shirt Mens XL Long Sleeve Crew Neck Embroidered Logo Green Abercrombie and Fitch Shirt Adult Medium Black Floral Print Short Sleeve 46155 Abercrombie & Fitch Men’s Embroidered Logo Hoodie Size Large Blue Abercrombie & Fitch Jeans 26 Super Skinny Burgundy Inseam 27.5″ Raw Hem New NWT Abercrombie Y2K Bootcut Jeans Womens Sz 8 Blue Gray Stretch Denim A&F Grunge VTG Abercrombie & Fitch Shirt Mens XL Short Sleeve Single Stitch Tee Abercrombie & Fitch Men Shorts 33 Blue Jean Cutoff Distressed Inseam 14″ READ Vintage Abercrombie & Fitch Shirt Mens MEDIUM Long Sleeve Muscle Striped Y2K Abercrombie & Fitch Soft A&F Short Sleeve T Shirt embroidered Y2k Men’s Sz S VINTAGE Abercrombie & Fitch Shirt Mens XL Grunge Aqua Slim Muscle Adult y2k 2000 VTG Men’s M Abercrombie Fitch New York Green Muscle T Shirt Medium Y2K 2000s Pink Floyd Music Abercrombie & Fitch T-Shirt Men Small S Short Sleeve White Pink Abercrombie & Fitch T Shirt Mens Medium 2018 Challenge Crewneck Maroon Promo Abercrombie & Fitch Shirt Men’s Size XL Solid Gray Poly Fleece Henley Pullover VINTAGE Abercrombie & Fitch Shirt Mens XXL Muscle Slim Green Adult y2k 2000s 2XL Abercrombie Fitch Shirt Mens Large Muscle Brown Short Sleeve Crew Neck Abercrombie & Fitch Cream Crew Neck Long Sleeve Tee Academia Preppy Mens Large Abercrombie & Fitch muscle shirt long sleeve sweater waffle knit neutral men’s L Abercrombie & Fitch ~ Away weekend EDP spray 3.4FL.OZ/100ml *Sealed Authentic* Vintage Abercrombie And Fitch Vest Adult 2XL XXL Yellow Fleece Lined Men’s Abercrombie Fitch Vintage Tee Mens Large Fitted T-Shirt MUSCLE Maroon Red Nice! Abercrombie and Fitch Men’s Muscle Tee Shirt, Size Large, Black. VTG Y2K Abercrombie & Fitch Mens XL Off White Waffle Knit Muscle Shirt Thermal Abercrombie & Fitch Muscle Shirt Men’s Blue Short Sleeve Tee New York City XS 【New】 Abercrombie & Fitch Men’s【A&F Moose Logo Henley Long Sleeve Tee】Grey @L $29 Abercrombie & Fitch Graphic Logo Tee Light Brown size XL ABERCROMBIE & FITCH DRAWSTRING CHINO SHORTS CREAM MENS 34 EXCELLENT CONDITION Vintage Abercrombie & Fitch Distressed Worn Cargo Shorts Men’s Sz 34 Abercrombie & Fitch Womens Top Large L Soft A&F Essentials Short Sleeve Camisa Abercrombie & Fitch Indian Chief Muscle Tee Size Small Abercrombie & Fitch Women’s White Spaghetti Strap Layered Cotton Summer Top XL Abercrombie & Fitch Men Shirt Large Blue Colorblock Y2K Logo Patched Muscle Abercrombie Shirt Adult Large Gray Solid Long Sleeve 49970 Abercrombie & Fitch henley tshirt mens M Medium pink stripe muscle fit short sl Abercrombie and Fitch New York Men’s Vintage Crew Neck Gray Muscle T-Shirt M Abercrombie and Fitch Henley Shirt Mens Large Hempl Blend Lightweight Preppy Vintage Abercrombie Fitch Shirt Mens Medium Yellow Distressed Preppy Classiccore Abercrombie & Fitch Orange & White T-Shirt 3D Lettering Cotton Crewneck Size XL Abercrombie & Fitch Long Sleeve Shirt Mens Sz S Blue Cotton 20 Spellout Logo Y2K VTG Men’s M Abercrombie Fitch New York Blue Muscle T Shirt Medium Y2K 2000s ABERCROMBIE & FITCH Blue INDIGO DYE MENS T-Shirt Medium-Wide Stripe Hard To See Abercrombie & Fitch Soft Tee Mens Basic T-Shirt Yellow Crew Neck Tee S Abercrombie & Fitch Shirt Men’s Size XL Muscle V-Neck Logo Gray Short Sleeve Y2K Abercrombie & Fitch T-Shirt Mens Large Long Sleeve Muscle Henley Embroidered Red Abercrombie & Fitch New women’s XXL off white linen blend Jacket Cropped Abercrombie & Fitch Jacket Mens Medium Noonmark GreenCamouflage Military Hoffman Vintage 90s Abercrombie and Fitch T-Shirt Size MEDIUM Red Baseball NWT Abercrombie & Fitch Size XL Red Muscle Long Sleeve Shirt Spell Out Heavy abercrombie fitch soft a&f tee long sleeve GRAY WITH WHITE size XL Abercrombie & Fitch Shirt Adult L Blue True Indigo Dye Preppy Casual Tee Mens Vintage Abercrombie Fitch Shirt Mens XL Short Sleeve Blue Abercrombie & Fitch Shirt Mens Small Blue White Red Long Sleeve Preppy Casual Abercrombie Fitch Shirt Mens Medium Henley Blue Long Sleeve Seersucker Collar Abercrombie Fitch Shorts Mens 30 Beige Cargo Pockets Surplus Twill Drawstring Abercrombie & Fitch Men’s M Tshirt Long Sleeve Green Abercrombie & Fitch Shirt Mens Medium A&F Muscle Fit Short Sleeve M Track Team Abercrombie & Fitch Distressed Patch Yellow Large T Shirt Tee Abercrombie & Fitch Shirt Mens Large Brown Thermal Knit T Shirt Big Spell Out Abercrombie & Fitch Muscle T Shirt V Neck Gray Green Blue Striped Moose Logo XL Vintage Abercrombie & Fitch Muscle Fit Long Sleeve Heavyweight Yellow Mens M Tee Abercrombie & Fitch Size Large Maroon Thermal Raw Hem Look Long Sleeve Shirt Abercrombie & Fitch Mens T- Shirt Size 3XL Red White SpellOut Casual Cotton Abercrombie & Fitch Mens Bermuda Shorts Size 28 Beige Tan Stretch Vtg Abercrombie Fitch Muscle Shirt XL Raglan Sleeves Burgundy Spell Out Abercrombie & Fitch The Mom High Rise Cotton Stretch Distressed Denim Jeans 36 Mens Pullover Fleece Hoodie